steel stockists
- Thread starter mark
- Start date
5150
Well-known member
Did a quick search, dunno if any of these can supply you, might be able to point you at the right place though:
Corus Service Centre
Chainbridge Road Industrial Estate, Blaydon-On-Tyne, Tyne and Wear NE21 5SS Tel: 0191 4142121
NT STEEL SERVICES
Unit 1, Metnor Business Park, Hadrian Rd, Wallsend, Tyne and Wear NE28 6HH Tel: 0191 263 7463
B.L.S Steels Ltd
12, Westfield Grove, Sunderland, Tyne and Wear SR4 8QZ Tel: 0191 5284900
Ro-Bal Steel Fabrication
Unit 18, Philadelphia Complex, Philadelphia, Houghton Le Spring, Tyne and Wear DH4 4UQ Tel: 0191 5121808
Corus Service Centre
Chainbridge Road Industrial Estate, Blaydon-On-Tyne, Tyne and Wear NE21 5SS Tel: 0191 4142121
NT STEEL SERVICES
Unit 1, Metnor Business Park, Hadrian Rd, Wallsend, Tyne and Wear NE28 6HH Tel: 0191 263 7463
B.L.S Steels Ltd
12, Westfield Grove, Sunderland, Tyne and Wear SR4 8QZ Tel: 0191 5284900
Ro-Bal Steel Fabrication
Unit 18, Philadelphia Complex, Philadelphia, Houghton Le Spring, Tyne and Wear DH4 4UQ Tel: 0191 5121808
mark
Well-known member
just measured it...
whats its for is the trailer for t'other boat. Snipe trailer and I took off the snipe sprung hubs - big long bar of sprung steel with a hub at each end, and replace with indepsension units. the big long batr sat inside a U shaped steel crossmember... but, without the sprung bar there anymore the crossmember is bending, o I wanted to drop a piece of box section insed the U shaped section to restore its strength if the makes sense?
internal dimensions of the U shaped bit are 107mm by 50mm. the 50mm is less critical, as it could hang out the bottom, but would be nice to find something that would fit snuggle in the channel. length needed is 1500mm
failing all that, I might just replace the entire cross member! so that would be anything say 120mm x 60mm in section
whats its for is the trailer for t'other boat. Snipe trailer and I took off the snipe sprung hubs - big long bar of sprung steel with a hub at each end, and replace with indepsension units. the big long batr sat inside a U shaped steel crossmember... but, without the sprung bar there anymore the crossmember is bending, o I wanted to drop a piece of box section insed the U shaped section to restore its strength if the makes sense?
internal dimensions of the U shaped bit are 107mm by 50mm. the 50mm is less critical, as it could hang out the bottom, but would be nice to find something that would fit snuggle in the channel. length needed is 1500mm
failing all that, I might just replace the entire cross member! so that would be anything say 120mm x 60mm in section
mark
Well-known member
sounds perfect... anyone wanna buy 6m of box section!
how where does it get delivered?
I'm guessing it'll come on a big truck, whcih the chances of getting anywhere near my house are slim to say the least. the last big wagon that came up our track (16ton rigid) got stuck and was there for 4 days while a dry stone wall was dismantled for it to get back down!
how where does it get delivered?
I'm guessing it'll come on a big truck, whcih the chances of getting anywhere near my house are slim to say the least. the last big wagon that came up our track (16ton rigid) got stuck and was there for 4 days while a dry stone wall was dismantled for it to get back down!
Last edited:
davem2005
Well-known member
Ring me ...I got loads here in the shed 
Failing that if you go to carter steel at stockton it should be under 20 quid...get em to cut it to length and leave the leftover there.
If you want to bring the trailer over theres a decent selection of steel fab equipment here too Would be happy to help yah once I fixed my minor problem with the drive
Cheers
dave
Failing that if you go to carter steel at stockton it should be under 20 quid...get em to cut it to length and leave the leftover there.
If you want to bring the trailer over theres a decent selection of steel fab equipment here too Would be happy to help yah once I fixed my minor problem with the drive
Cheers
dave
Last edited:
